The writer is making a number of great points relating to How to Install a Bathtub in general in this article down below.
Setting up a bath tub isn't exactly rocket science, however it does call for solid plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately hard project. If the old bathtub is readily easily accessible, the project can move immediately; if you have to open a wall surface to get rid of the old tub as well as position the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. Make sure you have actually certified on your own for the job as well as fit trying it. Rather than employing a specialist to take over a halfway-completed project, it is much better to think about employing one prior to you start. Chances are you may need a specialist plumber to make tube links.
This write-up will certainly help you set up a new tub in your shower room if you have actually already purchased a brand-new bathtub and also do not require to change the arrangement of your previous water system pipes.
Your tools as well as material checklist ought to make up the following:
Getting ready for the Installment
To start with, the supporting framework supplied with the bath must be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to avoid pressure on the tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you use every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the needed placement. The wooden boards are helpful in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub till the spirit level checks out degree.
To install taps, fit all-time low of the furthest versatile faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water system and inspect all joints and also new pipework for leakages and tighten them if needed. Load the tub as well as also inspect the overflow electrical outlet and the regular outlet for leaks.
Ultimately, fix the bath paneling as defined in the maker's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bathtub has been made use of at least once as this will resolve it right into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin ensuring that the washing machines are in place between the tap as well as the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type ought to be linked to the tap ends initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, leading to complications with dampness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, and also can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the bath tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can crack rather very early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly offered on the market. It is suggested to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading about A Step-by-Step Guide to Installing a Bathtub? Make feedback down the page. We will be glad to listen to your thoughts about this review. Hoping to see you back again in the near future. Feel free to take a moment to share this page if you appreciated it. Thanks a bunch for your time. Please check up our site back soon.
Schedule A Service Call